Inactivation of the enveloped virus phi6 with hydrodynamic cavitation.

The COVID -19 pandemic reminded us that we need better contingency plans to prevent the spread of infectious agents and the occurrence of epidemics or pandemics. Although the transmissibility of SARS-CoV-2 in water has not been confirmed, there are studies that have reported on the presence of infectious coronaviruses in water and wastewater samples. Since standard water treatments are not designed to eliminate viruses, it is of utmost importance to explore advanced treatment processes that can improve water treatment and help inactivate viruses when needed. This is the first study to investigate the effects of hydrodynamic cavitation on the inactivation of bacteriophage phi6, an enveloped virus used as a SARS-CoV-2 surrogate in many studies. In two series of experiments with increasing and constant sample temperature, virus reduction of up to 6.3 logs was achieved. Inactivation of phi6 at temperatures of 10 and 20 °C occurs predominantly by the mechanical effect of cavitation and results in a reduction of up to 4.5 logs. At 30 °C, the reduction increases to up to 6 logs, where the temperature-induced increased susceptibility of the viral lipid envelope makes the virus more prone to inactivation. Furthermore, the control experiments without cavitation showed that the increased temperature alone is not sufficient to cause inactivation, but that additional mechanical stress is still required. The RNA degradation results confirmed that virus inactivation was due to the disrupted lipid bilayer and not to RNA damage. Hydrodynamic cavitation, therefore, has the potential to inactivate current and potentially emerging enveloped pathogenic viruses in water at lower, environmentally relevant temperatures.

Using Different Surface Energy Models to Assess the Interactions between Antiviral Coating Films and phi6 Model Virus.

High molecular weight chitosan (HMWCh), quaternised cellulose nanofibrils (qCNF), and their mixture showed antiviral potential in liquid phase, while this effect decreased when applied to facial masks, as studied in our recent work. To gain more insight into material antiviral activity, spin-coated thin films were prepared from each suspension (HMWCh, qCNF) and their mixture with a 1:1 ratio. To understand their mechanism of action, the interactions between these model films with various polar and nonpolar liquids and bacteriophage phi6 (in liquid phase) as a viral surrogate were studied. Surface free energy (SFE) estimates were used as a tool to evaluate the potential adhesion of different polar liquid phases to these films by contact angle measurements (CA) using the sessile drop method. The Fowkes, Owens-Wendt-Rabel-Kealble (OWRK), Wu, and van Oss-Chaudhury-Good (vOGC) mathematical models were used to estimate surface free energy and its polar and dispersive contributions, as well as the Lewis acid and Lewis base contributions. In addition, the surface tension SFT of liquids was also determined. The adhesion and cohesion forces in wetting processes were also observed. The estimated SFE of spin-coated films varied between mathematical models (26-31 mJ/m2) depending on the polarity of the solvents tested, but the correlation between models clearly indicated a significant dominance of the dispersion components that hinder wettability. The poor wettability was also supported by the fact that the cohesive forces in the liquid phase were stronger than the adhesion to the contact surface. In addition, the dispersive (hydrophobic) component dominated in the phi6 dispersion, and since this was also the case in the spin-coated films, it can be assumed that weak physical van der Waals forces (dispersion forces) and hydrophobic interactions occurred between phi6 and the polysaccharide films, resulting in the virus not being in sufficient contact with the tested material during antiviral testing of the material to be inactivated by the active coatings of the polysaccharides used. Regarding the contact killing mechanism, this is a disadvantage that can be overcome by changing the previous material surface (activation). In this way, HMWCh, qCNF, and their mixture can attach to the material surface with better adhesion, thickness, and different shape and orientation, resulting in a more dominant polar fraction of SFE and thus enabling the interactions within the polar part of phi6 dispersion.

Transfer of Phi6 bacteriophage between human skin and surfaces common to consumer-facing environments.

AIMS: This study aimed to determine the extent of Phi6 (Φ6) transfer between skin and surfaces relevant to consumer-facing environments based on inoculum matrix, surface type and contact time. METHODS AND RESULTS: Φ6 transfer rates were determined from skin-to-fomite and fomite-to-skin influenced by inoculum matrix (artificial saliva and tripartite), surface type (aluminium, plastic, stainless steel, touchscreen, vinyl and wood) and contact time (5 and 10 s). Significant differences in estimated means were observed based on surface type (both transfer directions), inoculum matrix (skin-to-fomite) and contact time (both transfer directions). During a sequential transfer experiment from fomite-to-skin, the maximum number of consecutive transfer events observed was 3.33 ± 1.19, 2.33 ± 1.20 and 1.67 ± 1.21 for plastic, touchscreen and vinyl, respectively. CONCLUSIONS: Contact time significantly impacted Φ6 transfer rates, which may be attributed to skin absorption dynamics. Surface type should be considered for assessing Φ6 transfer rates. SIGNIFICANCE AND IMPACT OF THE STUDY: Although the persistence of Φ6 on fomites has been characterized, limited data are available regarding the transfer of Φ6 among skin and fomites. Determining Φ6 transfer rates for surfaces in consumer-facing environments based on these factors is needed to better inform future virus transmission mitigation strategies.

Viral Preservation with Protein-Supplemented Nebulizing Media in Aerosols.

The outbreak of SARS-CoV-2 has emphasized the need for a deeper understanding of infectivity, spread, and treatment of airborne viruses. Bacteriophages (phages) serve as ideal surrogates for respiratory pathogenic viruses thanks to their high tractability and the structural similarities tailless phages bear to viral pathogens. However, the aerosolization of enveloped SARS-CoV-2 surrogate phi6 usually results in a >3-log10 reduction in viability, limiting its usefulness as a surrogate for aerosolized coronavirus in "real world" contexts, such as a sneeze or cough. Recent work has shown that saliva or artificial saliva greatly improves the stability of viruses in aerosols and microdroplets relative to standard dilution/storage buffers like suspension medium (SM) buffer. These findings led us to investigate whether we could formulate media that preserves the viability of phi6 and other phages in artificially derived aerosols. Results indicate that SM buffer supplemented with bovine serum albumin (BSA) significantly improves the recovery of airborne phi6, MS2, and 80α and outperforms commercially formulated artificial saliva. Particle sizing and acoustic particle trapping data indicate that BSA supplementation dose-dependently improves viral survivability by reducing the extent of particle evaporation. These data suggest that our viral preservation medium may facilitate a lower-cost alternative to artificial saliva for future applied aerobiology studies. IMPORTANCE We have identified common and inexpensive lab reagents that confer increased aerosol survivability on phi6 and other phages. Our results suggest that soluble protein is a key protective component in nebulizing medium. Protein supplementation likely reduces exposure of the phage to the air-water interface by reducing the extent of particle evaporation. These findings will be useful for applications in which researchers wish to improve the survivability of these (and likely other) aerosolized viruses to better approximate highly transmissible airborne viruses like SARS-CoV-2.

Performance evaluation of an electrostatic precipitator with a copper plate using an aerosolized SARS-CoV-2 surrogate (bacteriophage phi 6).

The global spread of severe acute respiratory syndrome coronavirus-2 (SARS-CoV-2) has reminded us of the importance of developing technologies to reduce and control bioaerosols in built environments. For bioaerosol control, the interaction between researchers and biomaterials is essential, and considering the characteristics of target pathogens is strongly required. Herein, we used enveloped viral aerosols, bacteriophage phi 6, for evaluating the performance of an electrostatic precipitator (ESP) with a copper-collecting plate (Cu-plate). In particular, bacteriophage phi 6 is an accessible enveloped virus that can be operated in biosafety level (BSL)-1 as a promising surrogate for SARS-CoV-2 with structural and morphological similarities. ESP with Cu-plate showed >91% of particle removal efficiency for viral aerosols at 77 cm/s of airflow face velocity. Moreover, the Cu-plate presented a potent antiviral performance of 5.4-relative log reduction within <15 min of contact. We believe that the evaluation of ESP performance using an aerosolized enveloped virus and plaque assay is invaluable. Our results provide essential information for the development of bioaerosol control technologies that will lead the post-corona era.

Highin vitroactivity of gold and silver nanoparticles from Solanum mammosum L. against SARS-CoV-2 surrogate Phi6 and viral model PhiX174.

The search for new strategies to curb the spread of the SARS-CoV-2 coronavirus, which causes COVID-19, has become a global priority. Various nanomaterials have been proposed as ideal candidates to inactivate the virus; however, because of the high level of biosecurity required for their use, alternative models should be determined. This study aimed to compare the effects of two types of nanomaterials gold (AuNPs) and silver nanoparticles (AgNPs), recognized for their antiviral activity and affinity with the coronavirus spike protein using PhiX174 and enveloped Phi6 bacteriophages as models. To reduce the toxicity of nanoparticles, a species known for its intermediate antiviral activity,Solanum mammosumL. (Sm), was used. NPs prepared with sodium borohydride (NaBH4) functioned as the control. Antiviral activity against PhiX174 and Phi6 was analyzed using its seed, fruit, leaves, and essential oil; the leaves were the most effective on Phi6. Using the aqueous extract of the leaves, AuNPs-Sm of 5.34 ± 2.25 nm and AgNPs-Sm of 15.92 ± 8.03 nm, measured by transmission electron microscopy, were obtained. When comparing NPs with precursors, both gold(III) acetate and silver nitrate were more toxic than their respective NPs (99.99% at 1 mg ml-1). The AuNPs-Sm were less toxic, reaching 99.30% viral inactivation at 1 mg ml-1, unlike the AgNPs-Sm, which reached 99.94% at 0.01 mg ml-1. In addition, cell toxicity was tested in human adenocarcinoma alveolar basal epithelial cells (A549) and human foreskin fibroblasts. Gallic acid was the main component identified in the leaf extract using high performance liquid chromatography with diode array detection (HPLC-DAD). The FT-IR spectra showed the presence of a large proportion of polyphenolic compounds, and the antioxidant analysis confirmed the antiradical activity. The control NPs showed less antiviral activity than the AuNPs-Sm and AgNPs-Sm, which was statistically significant; this demonstrates that both theS. mammosumextract and its corresponding NPs have a greater antiviral effect on the surrogate Phi bacteriophage, which is an appropriate model for studying SARS-CoV-2.

Surface Inactivation of a SARS-CoV-2 Surrogate with Hypochlorous Acid is Impacted by Surface Type, Contact Time, Inoculum Matrix, and Concentration.

Indirect contact with contaminated surfaces is a potential transmission route for COVID-19. Therefore, it is necessary to investigate convenient and inexpensive surface sanitization methods, such as HOCl, against severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2). The SARS-CoV-2 surrogate, Phi6 (~ 7 log PFU/mL), was prepared in artificial saliva and tripartite matrices, spot inoculated on coupons of either stainless steel or vinyl, and allowed to dry. The coupons were sprayed with either 500 ppm or 1000 ppm HOCl, and remained on the surface for 0 s (control), 5 s, 30 s, or 60 s. Samples were enumerated via the double agar overlay assay. Statistical analysis was completed in R using a generalized linear model with Quasipoisson error approximations. Time, concentration, surface type, and inoculum matrix were all significant contributors to log reduction at P = 0.05. Significant three-way interactions were observed for 1000 ppm, vinyl, and 60 s (P = 0.03) and 1000 ppm, tripartite, and 60 s (P = 0.0121). A significant two-way interaction between vinyl and 60 s was also observed (P = 0.0168). Overall, increased HOCl concentration and exposure time led to increased Phi6 reduction. Notably, the highest estimated mean log reduction was 3.31 (95% CI 3.14, 3.49) for stainless steel at 60 s and 1000 ppm HOCl in artificial saliva, indicating that this method of sanitization may not adequately reduce enveloped viruses to below infective thresholds.

Antiviral properties of porous graphene, graphene oxide and graphene foam ultrafine fibers against Phi6 bacteriophage.

As the world has experienced in the Coronavirus Disease 2019 pandemic, viral infections have devastating effects on public health. Personal protective equipment with high antiviral features has become popular among healthcare staff, researchers, immunocompromised people and more to minimize this effect. Graphene and its derivatives have been included in many antimicrobial studies due to their exceptional physicochemical properties. However, scientific studies on antiviral graphene are much more limited than antibacterial and antifungal studies. The aim of this study was to produce nanocomposite fibers with high antiviral properties that can be used for personal protective equipment and biomedical devices. In this work, 10 wt% polycaprolactone-based fibers were prepared with different concentrations (0.1, 0.5, 1, 2, 4 w/w%) of porous graphene, graphene oxide and graphene foam in acetone by using electrospinning. SEM, FTIR and XRD characterizations were applied to understand the structure of fibers and the presence of materials. According to SEM results, the mean diameters of the porous graphene, graphene oxide and graphene foam nanofibers formed were around 390, 470, and 520 nm, respectively. FTIR and XRD characterization results for 2 w/w% concentration nanofibers demonstrated the presence of graphene oxide, porous graphene and graphene foam nanomaterials in the fiber. The antiviral properties of the formed fibers were tested against Pseudomonas phage Phi6. According to the results, concentration-dependent antiviral activity was observed, and the strongest viral inhibition graphene oxide-loaded nanofibers were 33.08 ± 1.21% at the end of 24 h.

First Insights into the Antiviral Activity of Chitosan-Based Bioactive Polymers towards the Bacteriophage Phi6: Physicochemical Characterization, Inactivation Potential, and Inhibitory Mechanisms.

The outbreak of the worrisome coronavirus disease in 2019 has caused great concern among the global public, especially regarding the need for personal protective equipment with applied antiviral agents to reduce the spread and transmission of the virus. Thus, in our research, chitosan-based bioactive polymers as potential antiviral agents were first evaluated as colloidal macromolecular solutions by elemental analysis and charge. Three different types of low and high molecular weight chitosan (LMW Ch, HMW Ch) and a LMW Ch derivative, i.e., quaternary chitosan (quart-LMW Ch), were used. To explore their antiviral activity for subsequent use in the form of coatings, the macromolecular Chs dispersions were incubated with the model virus phi6 (surrogate for SARS-CoV-2), and the success of virus inactivation was determined. Inactivation of phi6 with some chitosan-based compounds was very successful (>6 log), and the mechanisms behind this were explored. The changes in viral morphology after incubation were observed and the changes in infrared bands position were determined. In addition, dynamic and electrophoretic light scattering studies were performed to better understand the interaction between Chs and phi6. The results allowed us to better understand the antiviral mode of action of Chs agents as a function of their physicochemical properties.

Chlorine efficacy against bacteriophage Phi6, a surrogate for enveloped human viruses, on porous and non-porous surfaces at varying temperatures and humidity.

While efficacy of chlorine against Phi6, a widely-used surrogate for pathogenic enveloped viruses, is well-documented, surfaces common to low-resource contexts are under-researched. We evaluated seven surfaces (stainless steel, plastic, nitrile, tarp, cloth, concrete, wood) and three environmental conditions-temperature (4, 25, 40 °C), relative humidity (RH) (23, 85%), and soiling-to determine Phi6 recoverability and the efficacy of disinfection with 0.5% NaOCl. Overall, Phi6 recovery was >4 log10 PFU/mL on most surfaces after drying 1 hour at all temperature/humidity conditions. After disinfection, all non-porous test conditions (48/48) achieved ≥4 LRV at 1 and 5 minutes of exposure; significantly more non-porous surfaces met ≥4 LRV than porous (p < 0.001). Comparing porous surfaces, significantly fewer wood samples met ≥4 LRV than cloth (p < 0.001); no differences were observed between concrete and either wood (p = 0.083) or cloth (p = 0.087). Lastly, no differences were observed between soil and no-soil conditions for all surfaces (p = 0.712). This study highlights infectious Phi6 is recoverable across a range of surfaces and environmental conditions, and confirms the efficacy of chlorine disinfection. We recommend treating all surfaces with suspect contamination as potentially infectious, and disinfecting with 0.5% NaOCl for the minimum contact time required for the target enveloped virus (e.g. Ebola, SARS-CoV-2).

UVC, UVB and UVA susceptibility of Phi6 and its suitability as a SARS-CoV-2 surrogate.

For SARS-CoV-2 disinfection systems or applications that are based on UVC, UVB or UVA irradiation, it would be desirable to have a SARS-CoV-2 surrogate for tests and development, which does not require a laboratory with a high biosafety level. The bacteriophage Phi 6, an enveloped RNA virus like coronaviruses, is an obvious candidate for such a surrogate. In this study, UVC, UVB and UVA log-reduction doses for Phi6 are determined by plaque assay. Log-reduction doses for SARS-CoV-2 are retrieved from a literature research. Because of a high variability of the published results, median log-reduction doses are determined for defined spectral ranges and compared to Phi6 data in the same intervals. The measured Phi6 log-reduction doses for UVC (254 nm), UVB (311 nm) and UVA (365 nm) are 31.7, 980 and 14 684 mJ/cm2, respectively. The determined median log-reduction doses for SARS-CoV-2 are much lower, only about 1.7 mJ/cm2 within the spectral interval 251-270 nm. Therefore, Phi6 can be photoinactivated by all UV wavelengths but it is much less UV sensitive compared to SARS-CoV-2 in all UV spectral ranges. Thus, Phi6 is no convincing SARS-CoV-2 surrogate in UV applications.

Antiviral Characterization of Advanced Materials: Use of Bacteriophage Phi 6 as Surrogate of Enveloped Viruses Such as SARS-CoV-2.

The bacteriophage phi 6 is a virus that belongs to a different Baltimore group than SARS-CoV-2 (group III instead of IV). However, it has a round-like shape and a lipid envelope like SARS-CoV-2, which render it very useful to be used as a surrogate of this infectious pathogen for biosafety reasons. Thus, recent antiviral studies have demonstrated that antiviral materials such as calcium alginate hydrogels, polyester-based fabrics coated with benzalkonium chloride (BAK), polyethylene terephthalate (PET) coated with BAK and polyester-based fabrics coated with cranberry extracts or solidified hand soap produce similar log reductions in viral titers of both types of enveloped viruses after similar viral contact times. Therefore, researchers with no access to biosafety level 3 facilities can perform antiviral tests of a broad range of biomaterials, composites, nanomaterials, nanocomposites, coatings and compounds against the bacteriophage phi 6 as a biosafe viral model of SARS-CoV-2. In fact, this bacteriophage has been used as a surrogate of SARS-CoV-2 to test a broad range of antiviral materials and compounds of different chemical natures (polymers, metals, alloys, ceramics, composites, etc.) and forms (films, coatings, nanomaterials, extracts, porous supports produced by additive manufacturing, etc.) during the current pandemic. Furthermore, this biosafe viral model has also been used as a surrogate of SARS-CoV-2 and other highly pathogenic enveloped viruses such as Ebola and influenza in a wide range of biotechnological applications.

Biocompatible Films of Calcium Alginate Inactivate Enveloped Viruses Such as SARS-CoV-2.

The current pandemic is urgently demanding the development of alternative materials capable of inactivating the severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) that causes the coronavirus 2019 (COVID-19) disease. Calcium alginate is a crosslinked hydrophilic biopolymer with an immense range of biomedical applications due to its excellent chemical, physical, and biological properties. In this study, the cytotoxicity and antiviral activity of calcium alginate in the form of films were studied. The results showed that these films, prepared by solvent casting and subsequent crosslinking with calcium cations, are biocompatible in human keratinocytes and are capable of inactivating enveloped viruses such as bacteriophage phi 6 with a 1.43-log reduction (94.92% viral inactivation) and SARS-CoV-2 Delta variant with a 1.64-log reduction (96.94% viral inactivation) in virus titers. The antiviral activity of these calcium alginate films can be attributed to its compacted negative charges that may bind to viral envelopes inactivating membrane receptors.

Factors Impacting Persistence of Phi6 Bacteriophage, an Enveloped Virus Surrogate, on Fomite Surfaces.

The persistence of Phi6 (Φ6) bacteriophage on surfaces commonly encountered in consumer-facing environments was evaluated. Φ6 has been utilized as a surrogate for enveloped viruses, including SARS-CoV-2-the causative agent of COVID-19-due to structural similarities, biosafety level 1 (BSL-1) status, and ease of use. Φ6 persistence on fomites was evaluated by characterizing the impact of the inoculum matrix (artificial saliva, phosphate-buffered saline [PBS], tripartite), inoculum level (low and high), and surface type (nonporous-aluminum, stainless steel, plastic, touchscreen, vinyl; porous-wood). Φ6 was inoculated onto surfaces at low and high inoculum levels for each inoculum matrix and incubated (20.54 ± 0.48°C) for up to 168 h. Φ6 was eluted from the surface and quantified via the double agar overlay assay to determine virus survival over time. For nonporous surfaces inoculated with artificial saliva and PBS, significantly higher D values were observed with high inoculum application according to the 95% confidence intervals. In artificial saliva, D values ranged from 1.00 to 1.35 h at a low inoculum and 4.44 to 7.05 h at a high inoculum across inoculation matrices and surfaces. D values for Φ6, regardless of the inoculum level, were significantly higher in tripartite than in artificial saliva and PBS for nonporous surfaces. In contrast with artificial saliva or PBS, D values in tripartite at low inoculum (D values ranging from 45.8 to 72.8 h) were greater than those at high inoculum (D values ranging from 26.4 to 45.5 h) on nonporous surfaces. This study characterized the impact of the inoculum matrix, inoculum level, and surface type on Φ6 survival on various surfaces relevant to fomite transmission in public settings. IMPORTANCE An important consideration in virus contact transmission is the transfer rate between hands and surfaces, which is driven by several factors, including virus persistence on inanimate surfaces. This research characterized Φ6 persistence on surfaces commonly encountered in public settings based on various factors. The inoculum matrix, which simulates the route of transmission, can impact virus persistence, and three separate matrices were evaluated in this study to determine the impact on Φ6 persistence over time. The number of microorganisms has also been suggested to impact persistence, which was evaluated here to simulate real-world contamination scenarios on six surface types. Results from this study will guide future research utilizing Φ6 or other surrogates for enveloped viruses of public health concern.

Phi 6 Bacteriophage Inactivation by Metal Salts, Metal Powders, and Metal Surfaces.

The interaction of phages with abiotic environmental surfaces is usually an understudied field of phage ecology. In this study, we investigated the virucidal potential of different metal salts, metal and ceramic powders doped with Ag and Cu ions, and newly fabricated ceramic and metal surfaces against Phi6 bacteriophage. The new materials were fabricated by spark plasma sintering (SPS) and/or selective laser melting (SLM) techniques and had different surface free energies and infiltration features. We show that inactivation of Phi6 in solutions with Ag and Cu ions can be as effective as inactivation by pH, temperature, or UV. Adding powder to Ag and Cu ion solutions decreased their virucidal effect. The newly fabricated ceramic and metal surfaces showed very good virucidal activity. In particular, 45%TiO2 + 5%Ag + 45%ZrO2 + 5%Cu, in addition to virus adhesion, showed virucidal and infiltration properties. The results indicate that more than 99.99% of viruses deposited on the new ceramic surface were inactivated or irreversibly attached to it.

Development and Application of a Polydimethylsiloxane-Based Passive Air Sampler to Assess Personal Exposure to SARS-CoV-2

Exhaled respiratory droplets and aerosols can carry infectious viruses and are an important mode of transmission for COVID-19. Recent studies have been successful in detecting airborne SARS-CoV-2 RNA in indoor settings using active sampling methods. The cost, size, and maintenance of these samplers, however, limit their long-term monitoring ability in high-risk transmission areas. As an alternative, passive samplers can be small, lightweight, and inexpensive and do not require electrical power or maintenance for continual operation. Integration of passive samplers into wearable designs can be used to better understand personal exposure to the respiratory virus. This study evaluated the use of a polydimethylsiloxane (PDMS)-based passive sampler to assess personal exposure to aerosol and droplet SARS-CoV-2. The rate of uptake of virus-laden aerosol on PDMS was determined in lab-based rotating drum experiments to estimate time-weighted averaged airborne viral concentrations from passive sampler viral loading. The passive sampler was then embedded in a wearable clip design and distributed to community members across Connecticut to surveil personal SARS-CoV-2 exposure. The virus was detected on clips worn by five of the 62 participants (8%) with personal exposure ranging from 4 to 112 copies of SARS-CoV-2 RNA/m(3), predominantly in indoor restaurant settings. Our findings demonstrate that PDMS-based passive samplers may serve as a useful exposure assessment tool for airborne viral exposure in real-world high-risk settings and provide avenues for early detection of potential cases and guidance on site-specific infection control protocols that preempt community transmission.

Development and verification of a test rig for inactivation of bacteria and (corona-) viruses by UVC air disinfection systems

The ongoing coronavirus pandemic spreads through airborne transmission and is therefore difficult to contain. However, coronaviruses are highly sensitive to UVC, so UVC air disinfection systems should be able to inactivate the virus. Unfortunately, so far there are only few possibilities to test the reduction of airborne viruses or other pathogens. A special test rig, which mainly consisted of a nebulizer and an airflow system, was developed to determine the antiviral and antibacterial efficiency of UVC air disinfection systems. In the assessment of such an UVC air disinfection system with nebulized Staphylococcus carnosus and a sampling period of 30 minutes, a mean bactericidal reduction of 3.70 log10 (99.98 %) was determined. For antiviral irradiation of the coronavirus surrogate phi6 a mean viral load reduction of 1.18 log10 (93.40 %) was observed after a sampling period of 10 minutes. Therefore, mobile UVC air disinfection systems could be applied in hospitals, retirement and nursing homes. © 2021 by Walter de Gruyter Berlin/Boston.

Non-Woven Infection Prevention Fabrics Coated with Biobased Cranberry Extracts Inactivate Enveloped Viruses Such as SARS-CoV-2 and Multidrug-Resistant Bacteria.

The Coronavirus Disease (COVID-19) pandemic is demanding the rapid action of the authorities and scientific community in order to find new antimicrobial solutions that could inactivate the pathogen SARS-CoV-2 that causes this disease. Gram-positive bacteria contribute to severe pneumonia associated with COVID-19, and their resistance to antibiotics is exponentially increasing. In this regard, non-woven fabrics are currently used for the fabrication of infection prevention clothing such as face masks, caps, scrubs, shirts, trousers, disposable gowns, overalls, hoods, aprons and shoe covers as protective tools against viral and bacterial infections. However, these non-woven fabrics are made of materials that do not exhibit intrinsic antimicrobial activity. Thus, we have here developed non-woven fabrics with antimicrobial coatings of cranberry extracts capable of inactivating enveloped viruses such as SARS-CoV-2 and the bacteriophage phi 6 (about 99% of viral inactivation in 1 min of viral contact), and two multidrug-resistant bacteria: the methicillin-resistant Staphylococcus aureus and the methicillin-resistant Staphylococcus epidermidis. The morphology, thermal and mechanical properties of the produced filters were characterized by optical and electron microscopy, differential scanning calorimetry, thermogravimetry and dynamic mechanical thermal analysis. The non-toxicity of these advanced technologies was ensured using a Caenorhabditis elegans in vivo model. These results open up a new prevention path using natural and biodegradable compounds for the fabrication of infection prevention clothing in the current COVID-19 pandemic and microbial resistant era.

UV Inactivation of SARS-CoV-2 across the UVC Spectrum: KrCl* Excimer, Mercury-Vapor, and Light-Emitting-Diode (LED) Sources.

Effective disinfection technology to combat severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) can help reduce viral transmission during the ongoing COVID-19 global pandemic and in the future. UV devices emitting UVC irradiation (200 to 280 nm) have proven to be effective for virus disinfection, but limited information is available for SARS-CoV-2 due to the safety requirements of testing, which is limited to biosafety level 3 (BSL3) laboratories. In this study, inactivation of SARS-CoV-2 in thin-film buffered aqueous solution (pH 7.4) was determined across UVC irradiation wavelengths of 222 to 282 nm from krypton chloride (KrCl*) excimers, a low-pressure mercury-vapor lamp, and two UVC light-emitting diodes. Our results show that all tested UVC devices can effectively inactivate SARS-CoV-2, among which the KrCl* excimer had the best disinfection performance (i.e., highest inactivation rate). The inactivation rate constants of SARS-CoV-2 across wavelengths are similar to those for murine hepatitis virus (MHV) from our previous investigation, suggesting that MHV can serve as a reliable surrogate of SARS-CoV-2 with a lower BSL requirement (BSL2) during UV disinfection tests. This study provides fundamental information on UVC's action on SARS-CoV-2 and guidance for achieving reliable disinfection performance with UVC devices. IMPORTANCE UV light is an effective tool to help stem the spread of respiratory viruses and protect public health in commercial, public, transportation, and health care settings. For effective use of UV, there is a need to determine the efficiency of different UV wavelengths in killing pathogens, specifically SARS-CoV-2, to support efforts to control the ongoing COVID-19 global pandemic and future coronavirus-caused respiratory virus pandemics. We found that SARS-CoV-2 can be inactivated effectively using a broad range of UVC wavelengths, and 222 nm provided the best disinfection performance. Interestingly, 222-nm irradiation has been found to be safe for human exposure up to thresholds that are beyond those effective for inactivating viruses. Therefore, applying UV light from KrCl* excimers in public spaces can effectively help reduce viral aerosol or surface-based transmissions.

Transfer Rate of Enveloped and Nonenveloped Viruses between Fingerpads and Surfaces.

Fomites can represent a reservoir for pathogens, which may be subsequently transferred from surfaces to skin. In this study, we aim to understand how different factors (including virus type, surface type, time since last hand wash, and direction of transfer) affect virus transfer rates, defined as the fraction of virus transferred, between fingerpads and fomites. To determine this, 360 transfer events were performed with 20 volunteers using Phi6 (a surrogate for enveloped viruses), MS2 (a surrogate for nonenveloped viruses), and three clean surfaces (stainless steel, painted wood, and plastic). Considering all transfer events (all surfaces and both transfer directions combined), the mean transfer rates of Phi6 and MS2 were 0.17 and 0.26, respectively. Transfer of MS2 was significantly higher than that of Phi6 (P < 0.05). Surface type was a significant factor that affected the transfer rate of Phi6: Phi6 is more easily transferred to and from stainless steel and plastic than to and from painted wood. Direction of transfer was a significant factor affecting MS2 transfer rates: MS2 is more easily transferred from surfaces to fingerpads than from fingerpads to surfaces. Data from these virus transfer events, and subsequent transfer rate distributions, provide information that can be used to refine quantitative microbial risk assessments. This study provides a large-scale data set of transfer events with a surrogate for enveloped viruses, which extends the reach of the study to the role of fomites in the transmission of human enveloped viruses like influenza and SARS-CoV-2. IMPORTANCE This study created a large-scale data set for the transfer of enveloped viruses between skin and surfaces. The data set produced by this study provides information on modeling the distribution of enveloped and nonenveloped virus transfer rates, which can aid in the implementation of risk assessment models in the future. Additionally, enveloped and nonenveloped viruses were applied to experimental surfaces in an equivalent matrix to avoid matrix effects, so results between different viral species can be directly compared without confounding effects of different matrices. Our results indicating how virus type, surface type, time since last hand wash, and direction of transfer affect virus transfer rates can be used in decision-making processes to lower the risk of viral infection from transmission through fomites.